A quick look back: concentration and dilution
Last year, we learned about concentration and dilution. In this section, we will review both of those concepts, as they will be important tools moving forward.
Concentration: tells you how much solute is dissolved in a given volume of solution (mol/L).
Dilution: adds water to a solution which already has something dissolved in it. Therefore the litres change, but the moles don't.
Recall: When an ionic compound dissolves, each ion's concentration depends on how many of that ion are in the chemical formula.
For example, in Pb(NO3)2: if we had a concentration of 0.1 M, that means we would have 0.1 M Pb2+ and 0.2 M NO3−.
In the simulation, we will see a quick review of making a solution in the lab, as we did last year, as well as diluting a solution. Click the “Next step” button to see how the calculations occur as we go from grams, to moles, to concentration.
Solubility rules review
The Data Booklet's solubility table sorts ionic compounds into two groups. Soluble means more than 0.1 mol/L dissolves at 25 °C. Everything else has low solubility.
In the simulation, choose soluble or low solubility for each compound. The card turns green for a correct answer and red for an incorrect one. Find the rules in your Chemistry Data Booklet on page 4.
- Notice: “low solubility” is not “zero”. The table only tells us which side of 0.1 mol/L a compound is on. It cannot tell us how much dissolves.
“Insoluble” still dissolves a little
Add AgCl to water and stir. Almost all of it sits on the bottom, but a tiny amount does dissolve. Once the water holds as much as it can, the solution is saturated.
Zoom in on a saturated solution. Ions leave the crystal surface and other ions land back on it, at the same rate. The amount of solid stops changing, but both processes keep going. This is the same dynamic equilibrium we saw with K.
- Watch: one scoop dissolves completely. The second scoop leaves solid behind, and the “Dissolved” value stops rising.
- Watch: in the window, an ion leaves the crystal and another one lands, again and again.
What do you notice?
We can see slightly soluble solids in everyday life. Click through the three examples in the simulation and write one question of your own about each one in your notebook.
There are no answers yet. Some of these come back later in the unit.
What is Ksp?
A saturated solution is at equilibrium, so it has a K value associated with it. For solids dissolving, we have a specific K value, called Ksp, or “Solubility Product”.
We write it like any K: products over reactants. As a reminder: the solid is left out, just as pure solids were left out of K before. That leaves only the ions, each raised to its coefficient, again, the PRODUCT of their SOLUBILITY.
At this point, there are three numbers for us to derive the Ksp.
Solubility (g/L)
Molar solubility of the salt (mol/L)
Solubility of each ion (mol/L)
g/L⇄÷ molar mass
mol/L⇄× ion counts
[ions]⇄into Ksp
Ksp
The HIGHER the Ksp, the more PRODUCTS are favoured, therefore, the more soluble the salt is.
The LOWER the Ksp, the more REACTANTS are favoured, the less soluble the salt is.
From Ksp to solubility: silver chloride
One way we use Ksp is to anticipate how much of a salt will dissolve. Follow similar ICE table steps to solve for solubility.
- Notice: after the last step, the readout appears under the steps. It shows the same numbers we calculated.
From Ksp to solubility: lead(II) iodide
PbI2 is different. Each formula unit gives one Pb2+ but two I−. Before we start, predict.
- Watch: the window's ion counts. There are always twice as many I− as Pb2+. That is where the 4 in 4x3 comes from: (2x)2 = 4x2.
A common slip is to write [I⁻] = x. That gives Ksp = x³ and a molar solubility about 1.6 times too big.
Working backwards: from a measurement to Ksp
In the lab, we measure something and work back to Ksp. There is more than one way to do it.
Strategy 1: mass. Evaporate a known volume of saturated solution and weigh what is left. 250.0 mL of saturated Mg(OH)2 leaves 1.63 mg of solid.
Strategy 2: conductivity. Dissolved ions let a solution carry an electric current. The more ions, the higher the conductivity. A conductivity probe can't name the ions, but it can tell us how many there are. First, measure standards of known concentration and plot a calibration line: conductivity against concentration. Then measure the saturated solution and read its concentration off the line.
Strategy 3: a pH probe. We add Mg(OH)2 to neutral water a little at a time and watch the pH. Once the pH stops rising, the solution is saturated. From the pH we find [OH−], and [Mg2+] is half of that. (pH and pOH are next unit. This is a preview.)
Every strategy depends on careful measurement. Record the volume in litres, keep the mass in grams, use distilled water (other ions would add to the conductivity), and keep the right number of significant figures. A small error in s grows in Ksp, because s is cubed.
- Notice: working backwards uses the same arrows as before, in the other direction.
- Notice: three different measurements, one Ksp. If two strategies disagree, check the measurements before the algebra.
Try it in the Sandbox
Open the Sandbox. Dissolve AgCl, then PbI2, until solid stays on the bottom. Check that the readouts match the answers we worked out here.
Our Ksp lab starts next. Bring the arrows from the Ksp section: g/L ⇄ mol/L ⇄ [ions] ⇄ Ksp.